10 Things That Your Family Teach You About Fiat Panda Key Fob Replacement

Reasons Your fiat ducato key fob replacement 500 Key Fob Won't Work

A key fob with the Fiat Panda Key 500 number is a great way to open the doors and begin the car. There are many reasons why the fob may stop working. This includes a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement fiat 500 key replacement Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Modern key fobs operate with a limited range of operation, and must be within just a few feet of the vehicle to operate. If you're far from your car and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) by a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. You can find them in your local hardware store, or on the internet.

After you've replaced the battery in the coin cell you can test it by standing in front of your fiat key duplication 500 and pressing the buttons. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If your key fob isn't working even after replacing the battery, it may be water damage that hinders it from communicating with the module in your vehicle. Water damage can occur in a number of ways, ranging from an accidental splash to submerging the fob salt water at the beach. If you think your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this isn't working, you'll have to get your fob replaced by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually end up dying. The fob getting wet is not a good idea but if you drop it into an empty cup of water, or forget to remove it from your pants pocket before running the washing machine, don't give up hope.

First, remove the battery from the fob. Clean the electronic chip using isopropyl ethanol or a similar product and dry it completely before replacing the battery. Next try the fob and test if it works. If the fob doesn't work then it might need to be reset. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your vehicle it is likely to need to be replaced completely. This is an easy process that can be handled by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition in your vehicle. The locksmith will also have to program your fob into the car's system. This is a low-cost and fast process that can be completed in the same day.

Receiver Module Issues

One of the main reasons your 500 key fob could stop functioning is because it's out of range. The remote typically has an operating range of 30 feet or less and if it's far away from your car it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob doesn't function It could be because of an internal circuit board issue. Reprogramming the fob is usually the solution to this problem. You can find the steps for the majority of vehicles on YouTube or in the owner's manual.

You may have to replace the metal clips that hold the coin battery in place. If they loose tension, it could prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances the fob could be desync'd with your vehicle due to software problems or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases they might need to install the software again in your body control module, too.

Interference

Interference can also cause the key fob not to receive or transmit signals. This could occur if the key fob is close to the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob could not function could be due to a weak connection to the buttons, damage to the internal chip or water damage.

If the key fob has suddenly stopped working, in the middle of the night or after trying every option at home to solve it e.g. You might have a damaged 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module is located under the dash and picks up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting every single system on board in your 500 keys, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable first then the positive cable. Then, reconnect the battery. This will erase any remaining electric current, and also restart the computer of your car. This could help you get your key fob to function again. If the issue continues you should speak with an experienced technician. They will be able to determine the exact cause of your problems.