A Positive Rant Concerning Fiat Panda Key Fob Replacement

Reasons Your fiat 500 replacement key cost 500 Key Fob Won't Work

A Fiat 500 Key programming 500 key fob allows you to easily open doors and start your vehicle. There are many reasons why the key fob might stop working. This includes a dead coin-battery and water damage, as well as problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat punto key Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). Includes trunk, lock and unlock buttons.

Dead Coin Battery

The most common reason your 500 key fob won't work is an inactive battery. Modern key fobs come with a limited operating range and should be within just a few feet of the car to operate. If you are further away from your car and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens then replace the battery for your coin-cell (Part Number CR2032) by a brand new one of a trusted brand like Panasonic Duracell or Energizer. You can find them at the local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your fiat 500 replacement key uk 500. The parking lights will flash and the key fob will operate the lock and unlock switch.

If the fob's key doesn't work after replacing the battery, it might have water damage that stops it from connecting to the receiver module in your car. Water damage can occur in many ways, such as simply splashing or submerging your key fob in saltwater at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture out. If that doesn't work your fob is likely to need to be reprogrammed by an experienced auto locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to short and eventually fail. Getting the fob wet is not an option but if you accidentally drop it into a glass of water or do not remember to remove it from your pants pocket prior to running the washer do not give up hope.

First remove the battery from the fob. Clean the electronic chip with isopropyl ethanol or a similar product and dry it completely before replacing the battery. Next check the fob to check if it functions. If the key doesn't work, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is newer and has never been programmed to your vehicle it is likely to need to be replaced completely. A professional locksmith in the automotive industry can complete this simple process. The locksmith will need the key to be cut to match the car's ignition. The locksmith will also need to reprogram your fob into the vehicle's system. This is a simple and affordable process that is usually completed on the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote has a range of 30 feet. Therefore, should you be too far from your vehicle it won't be able to respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.

If you've replaced the coin battery (commonly called a "button" or "watch") and your fob doesn't function, it could have an internal circuit board issue. Reprogramming the fob usually resolves this issue. You can find the procedure for the majority of vehicles on YouTube or in the owner's manual.

You may need to replace the metal clips that hold the coin battery in place. If they lose tension, it can stop your coin battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob can become out of connection with your vehicle as a result of hardware or software problems. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances they may have to reinstall the software on your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit signals. This could occur if the keyfob is located in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons the key fob may not function could be due to a weak connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while in the middle of the night or even after trying everything you can do at home to solve it e.g. battery replacement, reprogramming and using the spare fiat ducato key fob programming fob, you might have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's onboard system, including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electric current, and also restart the car's computer. This can help get your key fob to work again. If the issue continues you should speak with an experienced technician. They will be able to diagnose the exact cause of your problems.